TEL(405) 874-7736
ADDR2009 S Broadway Ave, Suite #200, Moore, OK, 73160
HRSMon-Sun: 7:00 AM - 7:00 PM
(405) 874-7736 2009 S Broadway Ave, Suite #200, Moore, OK, 73160 Mon-Sun: 7:00 AM - 7:00 PM
CALL (405) 874-7736
// INSULATION · MOORE, OK

Insulation Contractor in Moore, OK for Cooler Summers and Lower OG&E Bills

On a sunny July afternoon in Moore, a poorly vented attic can hit 130–150°F. Your ductwork and air handler sit up there in that heat. Then January brings north winds that push cold air through every gap around your top plates and can lights. A lot of Moore homes were built fast, or rebuilt fast after the storms, with only minimum insulation, and a lot of that has settled to just a few inches. Moore Insulation Experts fixes the problem at the source. We measure what's actually in your attic and tell you what it needs, in plain terms. Then we install it right.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (1)
SpecialtyAttic Insulation
Service areaMoore, OK
Bonded insulation contractor
Fully insured crews
Financing available
Serving homes within a 20-mile radius of Moore
// ABOUT

We work on the houses you see around here every day: 1970s brick ranches in Eastmoore, post-2014 wind-code rebuilds near Plaza Towers and Briarwood, Tinker-era cottages in Del City, newer subdivisions in Norman and acreage shops out in Newcastle. Every job starts the same way. We inspect the attic, measure insulation depth, check air sealing and soffit baffles, and give you a clear written recommendation. We protect whatever you've got stored up there, work carefully around hurricane clips, and clean up completely when we're done.

20-MileService Radius Around Moore
18Metro Communities Served
36Insulation & Weatherization Services
R-49Attic Target for Zone 3A Homes
§ 03Local conditions

Why Moore Homes Need Better Insulation

Central Oklahoma puts insulation through a lot. Moore sits in IECC Climate Zone 3A, right in the middle of Tornado Alley, on clay soil that shrinks and swells. Add a building code that trails national energy standards, and many local homes end up working against their owners twelve months a year.

01

Heat, Freezes, Wind and Hail: Moore's Climate Pressure

July and August highs here average in the low-to-mid 90s°F. In hot years like 2011, when Oklahoma City set records for 100-degree days, triple digits stick around for weeks. Since most Moore homes have ducts and the air handler in the attic, that 130°F-plus air heats your cooled air before it ever reaches a vent. Winters cause trouble too. January lows average 28–30°F, and during Winter Storm Uri in February 2021 OKC dropped into the negative teens, freezing pipes in exterior walls and attics. Ice storms in December 2007 and October 2020 caused multi-day outages, and a tight, well-insulated house holds its temperature far longer when the power's out. Then there's the constant Oklahoma wind, which drives air through unsealed gaps. Spring hail, plus the 1999, 2003 and 2013 tornadoes, have left roof leaks behind that soak and ruin attic insulation.

02

Moore's Housing Stock: Ranches, Rebuilds and Settled Insulation

Moore grew as a bedroom suburb from the 1960s on, with big booms in the '70s–'80s and again in the 2000s. Most homes are single-story, wood-framed ranches with brick veneer, slab foundations and vented attics under asphalt shingles. Homes built before the 1990s usually started with R-11 to R-19 in the attic. Decades of settling, boxes stored on top and cable installers crawling through have compressed that further. Many of these houses have no soffit baffles and almost no air sealing at top plates or penetrations. Homes built after 2014 meet Moore's enhanced wind code and are generally tighter, but attic depth and air-sealing quality still vary a lot from one builder to the next. Nearby, Del City and Midwest City have 1940s–60s homes with shallow attics. Heritage Hills and Mesta Park have pier-and-beam houses with open crawlspaces.

03

Codes, Permits and Rules That Shape Insulation Work

Oklahoma adopts amended versions of the International Residential Code, and its energy provisions lag the latest IECC. In practice, local code minimums often fall below what the DOE recommends for Zone 3: R-30 to R-60 in attics, with the newest IECC calling for about R-49. Moore's 2014 wind code requires new and rebuilt homes to withstand roughly 135 mph winds using hurricane clips and straps. Our crews work around those connectors and never remove them. Insulation-only retrofits usually don't need a permit in Moore. Re-roofs, remodels and electrical or HVAC work often do, and those trades may need Construction Industries Board–licensed professionals. Insulation has to stay clear of non-IC-rated recessed lights. Suspected vermiculite should be tested for asbestos before anyone touches it. In OKC historic districts, exterior drill-and-fill requires a Certificate of Appropriateness.

04

What Metro Homeowners Value

Moore has roughly 60,000 residents, mostly families who own their homes and commute to OKC, Norman or Tinker Air Force Base. After years of tornado rebuilds and insurance claims, people here have learned to watch out for storm chasers. They want a local company that quotes clear R-values and shows before-and-after proof. Lower summer bills, comfort during heat waves and freezes, and help with utility or tax incentives are what usually drive the decision. OG&E and Oklahoma Natural Gas programs change over time, and so do federal credit dates, so we help you confirm what's currently available instead of promising it.

§ 04What we see most

Common Insulation Problems in Moore and the OKC Metro

Most calls we get start with a symptom: a hot back bedroom, a $400 July OG&E bill, a water stain after a hailstorm. Here are the insulation problems we find most often in Moore-area attics, walls and crawlspaces, why they happen here, and how serious each one is.

Moderate

Thin, Settled Attic Insulation

What it is

This is attic insulation that has compressed or settled well below its original depth. It often measures just 3–5 inches, about R-9 to R-15, against a recommended target near R-49. Loose fiberglass and old batts lose R-value as they pack down.

Why it is common in Moore

Most of Moore's housing went up between the 1960s and 1980s, when builders installed R-11 to R-19 and considered the job done. Forty-plus years of settling, storage boxes and HVAC techs or satellite installers walking across the attic floor have flattened it further. Oklahoma's energy code also lags the national IECC, so even some newer homes went in at minimums. With attics regularly passing 130°F, every missing inch shows up directly on the electric bill.

Signs you will notice

  • You can see ceiling joists poking above the insulation
  • Back bedrooms run 5–10°F warmer than the thermostat setting
  • The AC runs almost nonstop on 95°F afternoons
  • July and August electric bills jump sharply
  • Ceilings feel warm to the touch in summer
  • Insulation looks gray, flat or patchy

Moore-specific patterns

We see this all the time in Eastmoore near Little River Park, Old Town Moore and the South OKC homes along the I-240 corridor. Del City and Midwest City homes near Tinker often have even less, sometimes only original 1950s fill in shallow attics.

Severity

Moderate. Address within the next few months.

Typical solution

We air seal the attic floor, install baffles at the soffits, and blow in fiberglass or cellulose to about R-49. Depth rulers go in so you can verify the result yourself.

Serious

Storm-Damaged and Water-Soaked Insulation

What it is

Hail, wind and tornado damage can open the roof. Water then gets in and leaves insulation wet, matted, moldy or full of shingle grit and debris. Wet insulation loses most of its R-value and holds moisture against the drywall and framing.

Why it is common in Moore

Moore has taken direct tornado hits in 1999, 2003 and 2013, and large spring hail comes through most years. Roof replacements here are constant. Leaks sometimes go unnoticed for weeks, and May–June is when the region's 36–40 inches of annual rain peaks. Insurance claims add deadline pressure, so insulation is often the last thing anyone checks while the roof is being redone, and soaked material gets buried under new shingles.

Signs you will notice

  • Brown water stains on the ceiling
  • Musty smell from the attic or ceiling vents
  • Insulation clumped, dark or visibly wet
  • Debris or shingle granules in the attic
  • Sagging drywall
  • Mold spots on the roof decking

Moore-specific patterns

This is concentrated in the Plaza Towers and Briarwood area, Westmoore and other neighborhoods along past tornado paths. It also spikes across Moore, Norman and Newcastle after every major spring hail event.

Severity

Serious. Schedule a repair within 1–2 weeks.

Typical solution

We vacuum out the damaged insulation, document conditions with photos for your claim, let the decking dry, and reinstall new insulation to current R-value targets, coordinated with your roofer's schedule.

Moderate

Wind-Driven Air Leaks and Missing Air Sealing

What it is

These are unsealed gaps at top plates, wiring and plumbing penetrations, recessed lights, chases and attic hatches. They let conditioned air escape and outdoor air in. Insulation alone doesn't stop air movement, so air sealing has to come first.

Why it is common in Moore

Oklahoma's steady 10–20 mph winds put homes under constant pressure and push air through every opening. Older Moore ranches were built before air sealing was standard practice. The red Permian clay under central Oklahoma shrinks and swells, which shifts foundations and cracks drywall, brick and framing, so new leak paths keep opening even in sealed homes. Leaks also carry dust into the attic, and you'll see it as dark streaks in the insulation.

Signs you will notice

  • Drafts at outlets, baseboards and can lights
  • Dark, dirty streaks on attic insulation
  • Dust builds up fast indoors
  • Rooms feel cold on windy winter days
  • Attic hatch is unweatherstripped and loose
  • Cracks in drywall or brick veneer

Moore-specific patterns

This is common in 1970s–80s homes throughout Moore and South OKC. Homes with foundation movement show it the most, especially on expansive-clay lots in East Moore and parts of Midwest City.

Severity

Moderate. Address within the next few months.

Typical solution

We seal top plates, penetrations and chases with foam and caulk, fit IC-rated covers or proper clearances at recessed lights, and weatherstrip and insulate the attic hatch.

Serious

Rodent-Contaminated Insulation

What it is

Mice, rats, squirrels and raccoons tunnel through attic insulation, nest in it and leave urine and droppings behind. Contaminated insulation smells, loses R-value and can carry health risks. The safe fix is full removal and sanitizing.

Why it is common in Moore

Older neighborhoods with mature trees give squirrels an easy route onto roofs, and aging soffits and roof vents open up entry points. Rural and wooded properties in Newcastle, Noble and Bridge Creek see heavy wildlife pressure, especially as temperatures drop in the fall. Storm-loosened flashing and vents create new gaps, too.

Signs you will notice

  • Scratching or scurrying noises at night
  • Droppings on top of insulation
  • Tunnels and trails through the fill
  • Ammonia or urine odor
  • Chewed wiring or duct wrap
  • Nesting material near the eaves

Moore-specific patterns

We find this most in older tree-lined streets in Old Town Moore and Norman's Miller Historic District, and on acreage homes in Newcastle and Noble where fields and creeks sit right up against the property.

Severity

Serious. Schedule a repair within 1–2 weeks.

Typical solution

We vacuum out the contaminated insulation, sanitize the attic, seal common entry gaps, and reinstall clean or rodent-resistant insulation. We recommend a pest professional for active infestations.

Moderate

Sweating Ducts and Attic Condensation

What it is

Cold supply ducts running through hot, humid attics pull moisture out of the air when they're poorly insulated or leaky. They drip onto insulation and drywall. Over time, the result is water stains, mold and soggy ceilings.

Why it is common in Moore

Most Moore homes run their ductwork through the attic. Summer humidity is high, attic air sits above 130°F, and the AC pushes 55°F air through those ducts for hours at a time. Older R-4 duct wrap, crushed flex duct and unsealed joints let condensation form and conditioned air escape. You end up paying to cool the attic.

Signs you will notice

  • Water spots near ceiling registers
  • Dripping or wet duct wrap
  • Moldy insulation under ducts
  • Weak airflow in far rooms
  • Crushed or disconnected flex duct
  • Musty odor when the AC starts

Moore-specific patterns

This is widespread in Moore ranches from the 1980s and 2000s with long attic duct runs. It's also common in Norman's Hall Park and Brookhaven, where larger homes have extended trunk lines.

Severity

Moderate. Address within the next few months.

Typical solution

We seal duct joints with mastic, add or replace duct insulation, and bury ducts in blown insulation where practical. Licensed HVAC partners handle any mechanical repairs.

Serious

Cold Floors and Freeze Risk Over Crawlspaces

What it is

Pier-and-beam homes with open, vented or uninsulated crawlspaces lose heat through the floor. That leaves rooms cold and plumbing exposed to freezing. Damp crawlspaces also feed humidity and mold into the living space above.

Why it is common in Moore

Central OKC's 1910s–1940s neighborhoods were built on pier-and-beam foundations long before insulation codes existed. During Winter Storm Uri's below-zero lows, exposed crawlspace and exterior-wall pipes froze across the metro. Spring rains and summer humidity keep many of these crawlspaces damp much of the year.

Signs you will notice

  • Cold floors in winter
  • Pipes froze in 2021 or during ice storms
  • Musty smell in the house
  • Visible moisture or standing water below
  • Fallen or sagging floor batts
  • Cupping hardwood floors

Moore-specific patterns

This is concentrated in Heritage Hills, Mesta Park, Crown Heights and older parts of Nichols Hills. It also shows up in pier-and-beam homes near the OU campus in Norman.

Severity

Serious. Schedule a repair within 1–2 weeks.

Typical solution

We insulate the rim joists and floor or crawlspace walls, install a sealed vapor barrier, and encapsulate the space where moisture calls for it. We also insulate exposed pipes.

Emergency

Suspected Vermiculite in Older Attics

What it is

Vermiculite is a pebble-like, gray-brown or gold loose fill used in some older homes. Much of it came from a mine contaminated with asbestos. If it's disturbed without testing, fibers can get into the home's air.

Why it is common in Moore

Some metro homes built before 1950, and some updated in the decades after, contain vermiculite. Tinker-era Del City and Midwest City houses and older OKC neighborhoods are where it turns up. Under EPA and OSHA guidance, it should be tested before anyone removes or covers it.

Signs you will notice

  • Granular, shiny fill between joists
  • Gray-brown or golden pebble-like pieces
  • House built before roughly 1950
  • Fill found under newer insulation
  • Material inside wall cavities

Moore-specific patterns

We mostly see this in older Del City and Midwest City homes near Tinker, and in 1920s–40s houses in Mesta Park and Heritage Hills.

Severity

Emergency. Act within 24 hours to stop further damage.

Typical solution

We stop work and leave it alone. We recommend accredited testing and, if needed, licensed abatement before any insulation work moves forward.

§ 05Services

Insulation Services for Moore Homes and Buildings

No single material fits every building in the metro. A 1975 Moore ranch, a 1928 Mesta Park bungalow and a 40x60 metal shop in Bridge Creek each need something different. Here's what we install, how we do it, and where each option makes the most sense locally.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (3)
Specialty

Attic Insulation

What we do

We bring attics up to recommended R-values, usually around R-49, after measuring what's already there.

Methods & approach

First we air seal and install soffit baffles. Then we blow in fiberglass or cellulose with depth markers, keeping clearances at non-IC lights and the hatch.

Moore application

This is the biggest single fix for Moore's 130°F attics, where ducts and air handlers sit right in the heat.

Best for

Pre-1990s ranches with R-11 to R-19 and anyone fighting high July bills.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (4)
Specialty

Spray Foam Insulation

What we do

We apply open- or closed-cell spray foam that insulates and air seals in a single step.

Methods & approach

We assess each surface first, then spray foam on rooflines, walls, rim joists and shop panels with proper ventilation and protection.

Moore application

It stands up to wind-driven leaks and fills the odd cavities common in metro rebuilds and shops.

Best for

Conditioned attics, metal buildings, rim joists and premium whole-home projects.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (5)

Closed Cell Spray Foam

What we do

We install dense, moisture-resistant closed-cell foam that delivers high R-value per inch.

Methods & approach

It goes on in controlled passes to the specified thickness, adding rigidity and a vapor retarder.

Moore application

It's ideal for metal shops in Newcastle and Goldsby that would otherwise drip condensation, and for damp crawlspaces.

Best for

Metal buildings, crawlspace walls and tight spaces needing maximum R-value.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (6)

Blown-In Insulation

What we do

We machine-blow loose-fill fiberglass or cellulose into attics and enclosed cavities.

Methods & approach

We calibrate depth and density to hit the target R-value without excessive settling.

Moore application

It's the fast, affordable fix for the settled fill we find across Eastmoore and Del City.

Best for

Attic top-ups and full attic replacements.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (7)

Garage Insulation

What we do

We insulate garage walls, ceilings and bonus-room ceilings above garages.

Methods & approach

We use batts, blown fill or foam board depending on whether surfaces are open or finished.

Moore application

This keeps rooms above Moore garages comfortable. We work around in-ground storm shelters and wind-rated doors.

Best for

Bonus rooms, workshop garages and shared walls.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (8)

Crawl Space Insulation & Encapsulation

What we do

We insulate and seal crawlspaces to block moisture and cold.

Methods & approach

We insulate rim joists, install a sealed vapor barrier and insulate the walls or floor.

Moore application

It's critical for pier-and-beam homes in Heritage Hills, Mesta Park and Nichols Hills.

Best for

Cold floors, musty odors and freeze-prone plumbing.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (9)

Wall Insulation

What we do

We insulate open or closed exterior walls.

Methods & approach

For closed walls, we use drill-and-fill dense-pack after checking the wiring. For open framing, we use batts or foam.

Moore application

Many older Moore and Midwest City homes have empty walls. Historic OKC homes may need interior drilling to avoid exterior review.

Best for

Drafty older homes and remodels.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (10)

Ceiling Insulation

What we do

We insulate ceilings below attics and cathedral or vaulted ceilings.

Methods & approach

We use blown fill, batts or foam with proper vent channels.

Moore application

Vaulted living rooms in 2000s Moore homes often run hot all summer.

Best for

Vaulted ceilings and hot rooms.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (1)

Basement Insulation

What we do

We insulate the walls and rim joists of the few basements and below-grade rooms in the area.

Methods & approach

We use rigid foam board or closed-cell foam with moisture control.

Moore application

Basements are rare on Moore slabs, but they turn up in older OKC homes and some Norman custom builds.

Best for

Finished basements and below-grade rooms.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (2)

Floor Insulation

What we do

We insulate floors over crawlspaces, garages and open areas.

Methods & approach

We install batts with supports or spray foam to the subfloor.

Moore application

It warms cold floors in older pier-and-beam homes near OU in Norman.

Best for

Cold floors over crawlspaces.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (3)

Pipe & Duct Insulation

What we do

We wrap and seal ducts and insulate exposed pipes.

Methods & approach

We seal joints with mastic, add R-8 duct wrap and use pipe sleeves.

Moore application

It stops sweating attic ducts in summer and protects pipes from Uri-style freezes.

Best for

Attic ductwork and exposed plumbing.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (4)

Roof Insulation

What we do

We insulate the roof deck to create a conditioned attic or insulate low-slope roofs.

Methods & approach

We use spray foam or rigid boards under or over the deck.

Moore application

It brings attic ducts inside the thermal envelope, which pays off in Moore heat.

Best for

Homes with attic HVAC and commercial roofs.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (5)

Fiberglass Insulation

What we do

We install fiberglass batts and loose fill.

Methods & approach

Batts are cut to fit without gaps. Loose fill is blown to the specified density.

Moore application

It's the budget-friendly standard for Moore attics and new walls.

Best for

Cost-conscious attic and wall projects.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (6)

Cellulose Insulation

What we do

We install recycled, borate-treated cellulose.

Methods & approach

We blow loose fill in attics or dense-pack it in closed walls.

Moore application

Its density resists wind washing near soffits better than light fill.

Best for

Dense-pack walls and windy attics.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (7)

Batt Insulation

What we do

We install pre-cut batts in walls, floors and open attics.

Methods & approach

We friction-fit and split batts around wiring so they aren't compressed.

Moore application

It's common for remodels, additions and storm-damaged walls opened during repairs.

Best for

Open framing and new construction.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (8)

Rockwool & Mineral Wool Insulation

What we do

We install fire-resistant, moisture-tolerant mineral wool.

Methods & approach

It goes in as dense batts friction-fit in walls, floors and between rooms.

Moore application

It's a good fit near garages, mechanical rooms and walls where sound matters.

Best for

Fire resistance and sound control.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (9)

Foam Insulation

What we do

We use foam products for sealing and insulation.

Methods & approach

We apply canned foam, low-pressure kits or full spray foam, depending on scale.

Moore application

It seals gaps that keep opening as metro clay soils shift.

Best for

Gaps, penetrations and hard-to-reach cavities.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (10)

Foam Board & Rigid Insulation

What we do

We install rigid XPS, EPS or polyiso boards.

Methods & approach

Boards are cut and taped with sealed seams on walls, slabs, attic hatches and roofs.

Moore application

It's ideal for hatch covers, garage walls and storm shelter surrounds.

Best for

Continuous insulation and hatches.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (1)

Reflective & Radiant Barrier Insulation

What we do

We install radiant barriers that reflect roof heat.

Methods & approach

We staple foil to the rafters with an air gap, keeping vents clear.

Moore application

It cuts the radiant load from intense Oklahoma summer sun on dark shingles.

Best for

Hot attics with ductwork.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (2)

Vapor Barrier Installation

What we do

We install vapor retarders where moisture control is needed.

Methods & approach

We lay heavy poly with taped seams in crawlspaces and place retarders correctly for Zone 3A.

Moore application

It controls the humidity that rises from damp metro crawlspaces.

Best for

Crawlspaces and moisture-prone assemblies.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (3)

Soundproofing & Acoustic Insulation

What we do

We reduce noise between rooms and from outdoors.

Methods & approach

We use mineral wool, dense-pack and sealing at interior walls and ceilings.

Moore application

It's popular in Norman rentals and homes near busy I-35 and I-240.

Best for

Media rooms, bedrooms and rentals.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (4)

Rodent-Resistant Insulation

What we do

We install insulation treated to deter pests.

Methods & approach

We use borate-treated or pest-control products after cleanup and sealing.

Moore application

It helps in tree-lined Old Town Moore and on Noble or Newcastle acreage.

Best for

Attics with a history of rodents.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (5)

Eco-Friendly & Recycled Insulation Options

What we do

We offer recycled-content and lower-impact materials.

Methods & approach

Options include cellulose, recycled fiberglass and mineral wool.

Moore application

It's a common request from Norman professionals and owner-occupants.

Best for

Sustainability-minded homeowners.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (6)

High R-Value Insulation Installations

What we do

We design assemblies to hit R-49 to R-60.

Methods & approach

We layer blown fill over sealed floors or combine foam with fill.

Moore application

These exceed Oklahoma code minimums for top efficiency.

Best for

Maximum savings and long-term owners.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (7)

Residential Insulation Services

What we do

We cover whole-home insulation from attic to crawlspace.

Methods & approach

Every job starts with an inspection, then a prioritized plan and clean installation.

Moore application

We work on everything from Moore ranches to Nichols Hills estates.

Best for

Any homeowner in our 20-mile area.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (8)

Commercial Insulation Services

What we do

We insulate offices, retail and light commercial buildings.

Methods & approach

We use spray foam, batts and rigid board, scheduled around business hours.

Moore application

We serve strip centers and offices along I-35 and the I-240 corridor.

Best for

Business owners cutting energy costs.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (9)

Industrial Insulation Services

What we do

We insulate warehouses and industrial spaces.

Methods & approach

We use spray foam and rigid systems for large spans.

Moore application

We work in metro warehouses and shops near Tinker's industrial corridor.

Best for

Warehouses and production spaces.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (10)

New Construction Insulation

What we do

We insulate new homes and additions before drywall.

Methods & approach

We coordinate with builders, air seal, then install batts, foam or fill.

Moore application

We serve growing Mustang, Goldsby and Bridge Creek subdivisions and custom builds.

Best for

Builders and owner-builders.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (1)

Insulation Retrofit

What we do

We upgrade insulation in existing homes.

Methods & approach

We start with measurement and air sealing, then add insulation without major demolition.

Moore application

It's the go-to for 1960s–80s Moore and Del City homes.

Best for

Older homes underperforming today.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (2)

Metal Building Insulation

What we do

We insulate steel shops, barns and garages.

Methods & approach

We use closed-cell spray foam or faced blankets to stop condensation.

Moore application

These shops are common on Newcastle, Noble and Goldsby acreage.

Best for

Shops, barns and steel buildings.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (3)
Specialty

Insulation Removal & Replacement

What we do

We remove wet, moldy, rodent-fouled or storm-damaged insulation and replace it.

Methods & approach

We use a HEPA-filtered vacuum to remove it, sanitize, air seal and then reinstall.

Moore application

It's essential after Moore hail and tornado roof damage, and we coordinate around insurance timelines.

Best for

Storm-damaged, contaminated or failed attics.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (4)

Air Sealing Services

What we do

We seal the leaks that let wind blow through your home.

Methods & approach

We seal top plates, penetrations, chases, can lights and the hatch.

Moore application

It's vital given Oklahoma wind and shifting clay foundations.

Best for

Drafty, dusty homes.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (5)

Weatherization Services

What we do

We tighten up the whole home envelope.

Methods & approach

We combine air sealing, insulation, weatherstripping and duct sealing.

Moore application

It gets homes ready for heat waves and Uri-style freezes.

Best for

Budget-minded owners and small-town homes.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (6)

Drywall and Insulation Installation

What we do

We insulate and hang drywall in one project.

Methods & approach

We insulate open framing, then hang and finish the drywall.

Moore application

It's useful after storm repairs and garage conversions.

Best for

Repairs, remodels and garages.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (7)

Roofing and Insulation Services

What we do

We coordinate insulation with roof replacement.

Methods & approach

We schedule removal and reinstall around roof tear-off with permitted trades.

Moore application

It fits Moore's frequent hail re-roofs and protects wind-code clips.

Best for

Homes getting a new roof.

Moore Insulation Experts Insulation Contractor in Moore, OK project in Moore, OK (8)

ICF Installation Services

What we do

We install insulated concrete forms for walls.

Methods & approach

We stack foam forms with reinforcement for concrete placement.

Moore application

ICF gives storm-resistant, highly insulated walls suited to Tornado Alley.

Best for

New builds, safe rooms and shops.

§ 06How it works

Our Insulation Process, Start to Finish

We'll never quote from the driveway. Here's how every job runs, from the first attic look to the final cleanup, so you know exactly what to expect.

  1. 1
    Step 1

    Attic Inspection and Depth Measurement

    About 45–90 minutes, usually scheduled within a few days

    What happens

    • We measure insulation depth in several spots and estimate the current R-value
    • We check soffit baffles, air leaks, hatch condition and recessed light ratings
    • We look for moisture, storm damage, rodent activity or suspected vermiculite
    • We photograph what we find

    Moore considerations

    • In post-2014 homes, we note hurricane clips and straps so the crew protects them.
  2. 2
    Step 2

    Clear Recommendation and Honest Quote

    Same day or within 24–48 hours

    What happens

    • We give you a written plan with target R-values and materials
    • Pricing is itemized for air sealing, removal and insulation
    • We tell you whether any permit or licensed trade is needed
    • We go over financing options if you want them

    Moore considerations

    • We point you to current OG&E, ONG or federal incentives to verify yourself.
  3. 3
    Step 3

    Prep and Protection

    Morning of install, 30–60 minutes

    What happens

    • We lay drop cloths and protect floors along the path
    • We carefully move or cover stored attic items
    • We set up hoses and equipment outside
    • We mark wiring, junction boxes and fixtures

    Moore considerations

    • In summer, we start early to avoid peak attic heat.
  4. 4
    Step 4

    Air Sealing and Installation

    Most attics take 1 day; removal or spray foam adds 1–2 days

    What happens

    • We remove damaged insulation first, if needed
    • We seal top plates, penetrations and the hatch
    • We install baffles and clearances at non-IC lights
    • We install insulation to the specified depth with rulers in place

    Moore considerations

    • We coordinate with your roofer on storm-damage jobs.
  5. 5
    Step 5

    Walkthrough and Cleanup

    Final 30–60 minutes

    What happens

    • We clean the work area thoroughly
    • We show you before-and-after photos and depth markers
    • We put stored items back
    • We answer questions and hand over the documentation

    Moore considerations

    • Your photos and documentation can support insurance or rebate paperwork.
§ 07The difference

Why Moore Homeowners Choose Moore Insulation Experts

01

We Know Moore Attics Inside and Out

Moore houses tend to follow a few patterns, and we've learned them. The 1970s ranches in Eastmoore usually have flattened R-13 and no baffles. Rebuilds near Plaza Towers are tighter but uneven. Del City homes have shallow attics where every inch of clearance counts. That local knowledge helps us spot problems quickly and recommend what actually works for your house and our Zone 3A climate. You won't get a one-size-fits-all package written for some other part of the country, and you won't pay for upgrades your home doesn't need.

02

Bonded and Insured for Your Protection

After every big storm, Moore fills up with out-of-town crews who vanish once the checks clear. We're a bonded and insured insulation contractor, so you're protected if something goes wrong while we're in your home. Oklahoma doesn't issue a state license specifically for insulation. When a project involves wiring, bath fans or HVAC, we tell you up front and make sure the right Construction Industries Board–licensed trade handles that portion. You'll know exactly who's doing what, and that it's being done properly.

03

Every Job Starts With Real Measurements

Plenty of quotes in this market are guesses made from the driveway. We get into your attic, measure insulation depth in several places, check air sealing, soffit baffles and recessed lights, and look for moisture or pest damage. Then we put a clear recommendation in writing, with target R-values and the reasoning behind them. If your attic is already in good shape, we'll tell you. Sometimes a little air sealing is all you really need, and we'll say that too.

04

Honest, Itemized Pricing

Your quote breaks out air sealing, removal, baffles and insulation separately, so you can see where every dollar goes and pick the priorities that fit your budget. There are no pressure tactics and no 'today-only' discounts. Homeowners in the metro have been burned before, so we keep our pricing transparent and our scope clear. We can also discuss financing options to help you take on a bigger upgrade now instead of putting up with another expensive summer.

05

Storm-Damage Insulation Done Right

When hail or wind tears up your roof, wet and contaminated insulation has to come out before the new roof goes on. We vacuum out the damage, document conditions with photos you can use for your claim, let the decking dry and reinstall to current recommendations. We work around your roofer's schedule and your insurance deadlines, and we take care never to disturb the hurricane clips and straps Moore's 2014 wind code requires.

06

Right Material for Every Building Type

One week we're dense-packing walls in a 1920s Mesta Park home after checking for knob-and-tube remnants. The next, we're spraying closed-cell foam in a Goldsby metal shop or blowing R-49 into a Westmoore attic. Fiberglass, cellulose, batts, mineral wool, open- and closed-cell foam, rigid board and radiant barriers each have a place. We match the material to your structure, moisture conditions and budget, not to whatever's sitting on the truck.

07

Respect for Your Home and Belongings

Attics in this area are packed with holiday decorations, keepsakes and boxes. We protect your stored items, lay down drop cloths along our path and keep insulation out of your living space. Before we leave, we clean thoroughly and walk you through before-and-after photos and the depth markers. It's the kind of careful work we'd expect in our own homes.

§ 08Service area

Insulation Services Across Moore and the OKC Metro

We're based in Moore and serve homes and buildings within about 20 miles. That covers the inner metro's older neighborhoods, the Norman corridor to the south, and the fast-growing towns and acreage to the west and southwest. Each area has its own housing, and we plan around it.

Moore & South Metro Core

  • MooreOur home base, from Old Town and Eastmoore ranches to post-2014 wind-code rebuilds
  • Oklahoma CitySouth OKC along I-240, plus historic Heritage Hills and Mesta Park
  • Valley BrookModest older homes where affordable attic upgrades go a long way
  • NormanHall Park, Brookhaven and the Miller Historic District near OU
  • NobleRural homes and acreage with wildlife and crawlspace needs

East Metro & Tinker Corridor

  • Del City1940s–60s homes with shallow attics and minimal original insulation
  • Midwest CityTinker-era housing near the base, sometimes with vermiculite
  • Smith VillageSmall-town older homes needing settled-insulation fixes
  • Forest ParkEstablished homes on wooded lots
  • Nicoma ParkPrice-conscious owners with older housing stock
  • SpencerOlder frame homes that benefit from air sealing

West & Southwest Growth Areas

  • MustangNewer subdivisions with uneven builder-grade attic depth
  • NewcastleAcreage homes, metal shops and rodent-prone attics
  • Bridge CreekRural properties and manufactured homes
  • GoldsbyFast-growing area with new builds and steel shops
  • Warr AcresMid-century homes northwest of downtown OKC
  • BethanyEstablished neighborhoods with older attics
  • Nichols HillsLarge older homes suited to premium spray foam and air sealing

Coverage: We serve properties within roughly a 20-mile radius of Moore. If you're near the edge, call and we'll confirm.

Not sure if we serve your area? Call (405) 874-7736 and we will tell you right away.

§ 09Pricing

How Much Does Insulation Cost in Moore, OK?

What you'll pay depends on your attic size, what's already up there and the material you choose. Below are the main cost drivers we see on Moore-area projects, plus realistic ranges, so you can budget before your inspection.

What affects the price

  1. 1. Square Footage and Target R-Value Primary Factor factor

    Insulation is priced by area and depth. A 1,500 sq ft Moore ranch topped up from R-13 to R-49 needs far less material than a 3,000 sq ft Norman two-story starting from almost nothing. Going higher, to R-60, adds material cost but usually pays off over time in a climate with 95°F summers and attic HVAC. We quote by measured area and target R-value, so the numbers are easy to compare.

  2. 2. Removal of Old or Damaged Insulation Primary Factor factor

    Wet, moldy, storm-damaged or rodent-fouled insulation has to come out before new material goes in. Removal means HEPA vacuuming, disposal and often sanitizing, and it can roughly double a simple top-up's cost. If your insurer is covering hail or wind damage, our photo documentation helps support that part of the claim. Suspected vermiculite requires testing first, and abatement by a licensed firm is priced separately.

  3. 3. Material Choice Major Factor factor

    Blown fiberglass and cellulose are the most economical choice for attic floors. Batts cost a similar amount for open framing. Open-cell spray foam costs several times more per square foot. Closed-cell costs more still, but it adds air sealing, moisture resistance and structural rigidity. Radiant barriers are a moderate add-on. We'll explain the trade-offs so you only pay for performance your home actually benefits from.

  4. 4. Air Sealing and Prep Work Secondary Factor factor

    Sealing top plates, penetrations and the attic hatch, plus adding soffit baffles and recessed light clearances, adds labor. It's also where a big share of the comfort gain comes from in windy Oklahoma. Older Moore and Del City homes usually need more sealing than post-2014 builds. It typically adds a few hundred to around $1,500 depending on the house.

  5. 5. Access and Building Type Secondary Factor factor

    Shallow attics in Tinker-era homes, tight crawlspaces under historic OKC houses and tall metal shop walls all take more time and equipment. Closed walls in older homes need wiring checks before drill-and-fill. Historic district rules can affect methods, too. Easy-access, single-story Moore ranches are usually the most affordable.

Typical Moore projects

Attic top-up for a 1970s Moore ranch

About 1,600 sq ft, settled R-13 brought up to R-49 with blown fiberglass, baffles and basic air sealing

$2,000 – $3,800

Storm-damaged attic removal and replacement

About 1,800 sq ft, wet and debris-filled insulation removed, sanitized, air sealed and reinstalled to R-49

$4,000 – $7,500

Crawlspace encapsulation for an older OKC home

About 1,200 sq ft pier-and-beam crawlspace with sealed vapor barrier, rim-joist foam and wall insulation

$5,500 – $12,000

Closed-cell spray foam for a metal shop

40x60 steel building in Newcastle or Goldsby, walls and roof at about 2 inches closed-cell

$10,000 – $18,000

Financing available. Financing is available, so you can spread out the cost of larger projects like full removal, spray foam or encapsulation. Ask during your inspection.

Investment perspective. In homes with attic ductwork, bringing thin insulation up to around R-49 with proper air sealing often noticeably reduces summer cooling costs. It also helps your house hold its temperature through freezes and outages. Check current OG&E, ONG and federal incentives before you sign.

Schedule Free Energy Audit
§ 10Questions

Insulation FAQs for Moore Homeowners

How much does attic insulation cost in Moore?

Most Moore attic top-ups run about $2,000 to $3,800 for a typical 1,500–1,800 sq ft ranch going from settled R-13 or so up to R-49 with blown fiberglass, baffles and basic air sealing. If the old insulation is wet, moldy, rodent-damaged or full of storm debris, removal and sanitizing push most projects into the $4,000 to $7,500 range. Spray foam and conditioned-attic work cost more. We give an itemized quote after measuring your attic, and financing is available.

How long does an insulation job take?

A standard blown-in attic job usually takes one day, often just four to six hours, including air sealing and cleanup. Removal and replacement typically adds a day. Spray foam, crawlspace encapsulation and metal building projects can take one to three days depending on size. In July and August, we schedule early-morning starts because Moore attics get dangerously hot by mid-afternoon. You can stay home the whole time for most attic work.

Do I need a permit for insulation in Moore?

Usually not for insulation-only retrofits. Adding insulation to an existing attic generally doesn't require a building permit in Moore or most nearby cities. Permits typically do come into play when insulation is part of a re-roof, remodel, addition, or electrical or HVAC work, and those trades may need Construction Industries Board licensing. In OKC historic districts like Heritage Hills and Mesta Park, exterior drill-and-fill needs a Certificate of Appropriateness. Nichols Hills runs its own building department. We'll tell you what applies, but always confirm with your city.

How much attic insulation do I need in Oklahoma?

For Moore's Climate Zone 3A, the DOE recommends R-30 to R-60 in attics, and the latest IECC calls for about R-49. That's roughly 13–16 inches of blown fiberglass, depending on the product. Oklahoma's adopted code lags the newest standards, and many homes built before the 1990s started at R-11 to R-19 and have settled since. If you can see the tops of your ceiling joists, you're almost certainly well below the recommended level.

When should I replace insulation instead of adding more?

Replace it when it's wet, moldy, compressed by water, contaminated by rodents or full of storm debris. Adding fresh insulation over damaged material traps moisture and odors, and it hides the problem. After any Moore hail or wind event with a roof leak, have the attic checked before the new roof goes on. Old vermiculite is different. Don't cover or remove it until it's been tested for asbestos. Dry, clean insulation that's just thin can usually be topped up.

How can I prevent high summer bills and frozen pipes?

Start by air sealing the attic floor and bringing insulation up to about R-49, since most Moore homes run ducts through a 130°F-plus attic. Seal and insulate your ductwork so it doesn't sweat or leak. A radiant barrier can cut heat gain further. For winter, insulate exposed pipes, the rim joists and crawlspaces, especially in older pier-and-beam homes, and seal exterior wall penetrations. Those were the weak spots that froze during Winter Storm Uri in 2021.

Is spray foam or blown-in insulation better for my home?

For most Moore attic floors, blown-in fiberglass or cellulose with good air sealing gives the best value. Spray foam makes sense on rooflines when you want to bring attic ductwork inside a conditioned space, on metal shops prone to condensation, on rim joists and crawlspace walls, and in premium whole-home projects like the ones we see in Nichols Hills. Closed-cell foam also resists moisture and adds rigidity. We'll recommend the option that fits your structure and budget.

What signs mean I should call an insulation contractor now?

Call soon if you notice ceiling water stains after a storm, a musty attic smell, scratching noises overhead, rooms that run 5–10°F off the thermostat, or an AC that can't keep up on 95°F days. Dark streaks in your insulation, visible ceiling joists, drafty outlets and cold floors over a crawlspace are other signs. Wet insulation and rodent contamination get worse quickly, so don't wait on those. A quick inspection will tell you exactly where you stand.

Schedule Your Moore Attic Inspection Today

Don't spend another Oklahoma summer paying to cool your attic. We'll measure what's up there, explain what you actually need, and give you an honest price before any work starts. Roof leak or storm damage? Wet insulation should come out quickly. Call us so we can coordinate with your roofer and insurance timeline.

Call now(405) 874-7736Online schedulingBook a time that works
Office2009 S Broadway Ave, Suite #200, Moore, OK, 73160
HoursMon-Sun: 7:00 AM - 7:00 PM

Get your free quote

Your information is never shared.
Call Schedule